Directions of Use
Technical Specifications
Resources
Product reviews
Shipping & Return
Installation
- Mount the Controller on wall, place the sensor in a well- ventilated area.
- Connect the CO2 sensor to the controller.
- Plug the Controller into a 120V NEMA 5-15 wall outlet.
- Program the desired settings before connecting to CO2 generator or regulator.
- Plug the CO2 device into the power outlet of the unit. Ensure that the CO2 device has the proper voltage (120V) and not exceeding the max amperage rating (6A).
Operation Instructions
- Reading CO2 Level
a ). Warm up the unit for approximately 1 minute
b ). After warm-up, the LED will display the current CO2 level ( as PPM ).
c ). The CO2 Device LED will turn green when corrected with CO2 generator or CO2 regulator
- Maximum CO2 Recorded Value Recall
Press HOME button on time, the LED will display the maximum CO2 recorded value and the Max LED indicator will be blinking. To clear the record, press UP button or DOWN button, all digits on LED display will be blinking, press and hold HOME button for 3 second to clear the record.
- Minimum CO2 Recorded Value Recall
Press HOME button twice, the LED will display the minimum CO2 recorded value and the Min LED indicator will be blinking. To clear the record, press UP button or DOWN button, all digits on LED display will be blinking, press and hold HOME button for 3 second to clear the record.
- CO2 PPM Level Setpoint Adjustment
Factory setpoint is 1200 PPM, the CO2 sensor sensing the CO2 PPM level. If the CO2 level is lower than 1200 PPM, the controller will turn on output relay to drive the CO2 device for enriching the CO2 in the grow area. When the CO2 PPM level exceeds setpoint plus deadband (50 PPM), the controller will cut off the output. To adjust the setpoint, press HOME button 3 times, the Setpoint LED indicator will be blinking, the LED will display the current setpoint. Press UP or DOWN , all digits on the LED will be blinking and then press UP or DOWN button to increase or decrease the setpoint.
- CO2 PPM Deadband Adjustment
Factory deadband setting is 50 PPM. To adjust the deadband, press HOME button 4 times, the Deadband LED will be blinking and the LED will display the current deadband setting. Press UP or DOWN , the digits on the LED will be blinking and the press or to increase or decrease the deadband
- Fuzzy Logic Mode
a ). Fuzzy Logic mode counters rising or falling CO2 levels by quickly activating the CO2 solenoid valve, allowing CO2 levels to be controlled more precisely.
b ). The Fuzzy Logic function is active if the Fuzzy Logic LED indicator illuminated.
c ). Factory default setting of fuzzy logic is off. To activate the fuzzy logic, press HOME button 5 times, the Fuzzy Logic LED indicator will be blinking. Press UP or DOWN , the LED display OFF. Press or , the LED displays ON. Press HOME button to confirm and activate the fuzzy logic and the Fuzzy Logic LED indicator will illuminate.
d ). This function can be used ONLY with compressed CO2.
e). Do not use Fuzzy Logic with a CO2 generator ! ! !
- Calibrating the CO2 Sensor
a ). Place the sensor outdoors in a shaded area. Do not place in direct sunlight. Keep away from people, animals and other CO2 emitting units.
Note: if calibration will be in a high-traffic area or highly populated area, a slightly higher calibration value of 400-475 ppm is recommended.
b ). Plug in the Controller and allow it to warm up for a minimum of 30 minutes but 1 hour is recommended.
c ). Press HOME button 6 times to activate the automatic calibration, the [ Calibrat] LED indicator will be blinking. Press UP or DOWN , the CO2 level ( 400 ppm ) will be displayed on the LED and blinking. Press UP or DOWN to adjust the calibration level if you have an accurate reference. Otherwise, the recommended level will be 400 ppm. Press and hold HOME button 3 seconds to activate the calibration.
Note: DO NOT exhale or breathe near the sensor while activating the calibration function.
d ) The LED will display the countdown timing.
e ) When it is completed, the screen will display normal functions. Calibration will not affect any other settings.
Note: It may take up to 90 seconds to complete the calibration process.
- Restore the Factory Settings
Press and hold HOME button before plugging controller into wall outlet. Power the controller, the LED display "rESt " and blinks. Keep holding the HOME button for 5 seconds until the LED displays " donE ".
Technical Specifications
Input Voltage: 120 Volts ACOutput Relay Rating: 10A
Fuse Rating: 6A/250V~
AC Power Cord Length: 1.8m
CO2 Control Range: 400-2000 PPM
CO2 Deadband Range: 20-200 PPM
CO2 Accuracy: ±50 PPM
CO2 Sensor Type: NDIR (Nondispersive Infrared)
Packaging Dimensions: 275mm(L) x 87mm(W) x 94mm(H)
Gross Weight: 0.56kgs
Shipping cost is based on weight. Just add products to your cart and use the Shipping Calculator to see the shipping price. We want you to be 100% satisfied with your purchase. Items can be returned or exchanged within 30 days of delivery.